{"id":50046,"date":"2017-12-14T14:25:43","date_gmt":"2017-12-14T19:25:43","guid":{"rendered":"https:\/\/www.constructionspecifier.com\/?p=50046"},"modified":"2018-01-15T14:44:59","modified_gmt":"2018-01-15T19:44:59","slug":"defining-testing-construction-tape-flashing-durability","status":"publish","type":"post","link":"https:\/\/www.constructionspecifier.com\/defining-testing-construction-tape-flashing-durability\/","title":{"rendered":"Defining and testing construction tape and flashing durability"},"content":{"rendered":"
\"\"<\/a>
All images courtesy Building Diagnostics Inc.<\/span><\/em><\/figcaption><\/figure>\n

by Anthony M. Garcia, PE, and Jorge M. Blanco
\n<\/strong>Construction tapes and flashings are used to span joints and gaps, typically in conjunction with a primary water-resistive barrier (WRB) or air barrier. Since they are concealed behind cladding, it is important tapes and flashings are durable. Will they remain adhered in harsh conditions? Can they accommodate movement for the design life of the building? This article\u2019s authors performed hundreds of tests to evaluate different tape adhesive chemistries and durability on a variety of substrates.<\/p>\n

Most construction professionals are familiar with traditional rubberized asphalt self-adhered flashing (i.e. <\/em>peel and stick), but acrylic and butyl tapes are increasingly popular. Construction tapes and self-adhered membrane flashings (collectively referred to as \u2018tapes\u2019 in this article) are used to span gaps and transitions in materials, such as at window perimeters, sheathing joints, and other complex geometries.<\/p>\n

Tapes are common accessories in WRBs and air barriers such as sheet membranes, liquid membranes, and building wraps. These assemblies are crucial to a building\u2019s performance and durability. Since tapes are used at junctions critical for keeping the exterior out, proper selection and installation are paramount to avoid water infiltration and air leakage that may lead to tenant discomfort\u2014or worse.<\/p>\n

Defining the tapes
\n<\/strong>To define \u2018tape\u2019 and its function in construction, the authors reviewed numerous codes and standards, including the 2015 International Building Code<\/em> (IBC<\/em>) and 2015 International Energy Conservation Code<\/em> (IECC<\/em>).<\/p>\n

Regarding WRBs, IBC<\/em> requires:<\/p>\n

[n]ot fewer than one layer of No. 15 asphalt felt, complying with ASTM D226 [Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing<\/em>] for Type 1 felt or other approved materials, shall be attached to the studs or sheathing, with flashing as described in Section 1405.4, in such a manner as to provide a continuous water-resistive barrier behind the <\/em>exterior wall veneer.(This comes from the 2015 IBC<\/em> Chapter 14, Section 1404, Paragraph 1404.2.)<\/span>
\n<\/span><\/p>\n

Flashings, as defined by IBC<\/em>:<\/p>\n

prevent moisture from entering the wall or to redirect that moisture to the exterior\u201d, and \u201cshall be installed at the perimeters of exterior door and window assemblies, penetrations and terminations of exterior wall<\/em> assemblies\u2026 (See 2015 IBC<\/em> Chapter 14, Section 1404, Paragraph 1454.4.)<\/span>
\n<\/span><\/p>\n

IBC<\/em> does not require or define an air barrier. However, IECC <\/em>calls for an air barrier to be \u201ccontinuous\u201d and \u201cprovided throughout the building thermal envelope.\u201d (Excerpted from 2015 IECC<\/em> Chapter 4, Section C402, Paragraph C402.5.1.) For the air barrier, IECC<\/em> also requires:<\/p>\n

joints and seams shall be sealed, including sealing transitions in places and change in materials\u2026Joints and seals associated with penetrations shall be sealed in the same manner or taped or covered with moisture vapor-permeable wrapping material.(See 2015 IECC<\/em> Chapter 4, Section C402, Paragraph C402.5.1.1.3.)<\/span>
\n<\/span><\/p>\n

(The code specifically mentions \u201ctapes\u201d as part of the air barrier.)<\/p>\n

As IECC<\/em> recognizes tapes will be stressed during their service life, it requires sealing materials to be \u201csecurely installed around the penetration so as not to dislodge, loosen, or otherwise impair the penetrations\u2019 ability to resist positive and negative pressure from wind, stack effect, and mechanical ventilation.\u201d<\/p>\n

In addition to codes and standards, previous research and laboratory testing on WRBs informed the study discussed in this article.\u00a0<\/sup> (For more information, see the February 2015 issue of The Construction Specifier<\/em> for the article, \u201cDurability of Water-resistive Barriers,\u201d by Beth Anne Feero, EIT, and David H. Nicastro, PE. Visit www.constructionspecifier.com\/durability-of-water-resistive-barriers<\/a>.) During the construction of the WRB specimens for testing, manufacturers\u2019 accessory tapes were installed at many details; this experience helped develop tape testing methodology and provided a basis for product selection. Ongoing WRB testing will continue to inform future tape testing.<\/p>\n

For this study, tapes were defined as broadly as possible, while keeping IBC<\/em>, IECC<\/em>, and colloquial definitions in mind. The requirements for inclusion in the testing were purposely flexible.<\/p>\n

Tapes typically consist of similar components, including a carrier sheet (i.e.<\/em> facer or scrim)\u2014often made of polyethylene, polypropylene, or aluminum\u2014and an adhesive layer. A release paper (protective liner) is used on some products; one of the most challenging aspects of engineering a sticky tape is keeping it from adhering to itself on the roll.<\/p>\n

The adhesives used in tapes consist of long-chain polymers that interact with substrates under pressure. The polymers create physical bonds that must be very strong in the dynamic and critical applications of building tapes.(The Scientific American<\/em> article, \u201cWhat Exactly is the Physical or Chemical Process that Makes Adhesive Tape Sticky?,\u201d can be read online at www.scientificamerican.com\/article\/what-exactly-is-the-physi<\/a>.)<\/p>\n

Generally, the market is dominated by a few adhesives and their specific uses:<\/p>\n